technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 1 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen features B popular t-1 3/4 round package. B high efficiency. B available on tape and reel. B reliable and robust. B uv resistant epoxy B the product itself will remain within rohs complian t version . descriptions B the series is specially designed for applications requiring higher brightness. B the led lamps are available with different colors, intensities, epoxy colors, etc. applications B color graphic signs B message boards B variable message signs (vms) B commercial outdoor advertising device selection guide led part no. chip material emitted color lens color stopper 7383/y7c3-aqsb/ms no 7383/y7c3-aqsb/p/ms algainp brilliant yellow water clear yes
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 2 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen package dimensions no stopper type stopper type notes: B all dimensions are in millimeters, tolerance is 0.2 5mm except being specified. B protruded resin under flange is 1.5mm max led.
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 3 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen absolute maximum ratings (ta=25 ) parameter symbol rating units forward current i f 50 ma pulse forward current *1 i fp 160 ma operating temperature t opr -40 ~ +85 storage temperature t stg -40 ~ +100 electrostatic discharge esd 2k v soldering temperature *2 t sol 260 power dissipation p d 115 mw reverse voltage v r 5 v notes: soldering time Q 5 seconds. electro-optical characteristics (ta=25 ) parameter symbol condition min. typ. max. units forward voltage v f i f =20ma 1.8 2.0 2.6 v luminous intensity i v i f =20ma 3600 4500 7150 mcd viewing angle 2 1/2 i f =20ma -- 30 -- deg peak wavelength p i f =20ma -- 591 -- nm dominant wavelength d i f =20ma 586 589 594 nm spectrum radiation bandwidth ? i f =20ma -- 15 -- nm reverse current i r v r =5v -- -- 10 a
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 4 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen rank combination (i f =20ma) rank q r s luminous intensity 3600~4500 4500~5650 5650~7150 *measurement uncertainty of luminous intensity: 10% unit: :mcd rank 1 2 3 4 forward voltage 1.8~2.0 2.0~2.2 2.2~2.4 2.4~2.6 *measurement uncertainty of forward voltage: 0.1v unit:v rank 1 2 dominant wavelength 586~590 590~594 *measurement uncertainty of dominant wavelength 1.0nm unit:nm
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 5 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen 0 20 40 60 80 100 0 10 20 30 40 50 60 forward current(ma) ambient temperature ta( o c) 1.0 1.5 2.0 2.5 3.0 3.5 0 10 20 30 40 50 forward current(ma) forward voltage(v) 0 10 20 30 40 50 0.0 0.5 1.0 1.5 2.0 2.5 relative luminous intensity(a.u.) forward current(ma) 25 30 35 40 45 50 55 60 65 70 0.0 0.5 1.0 1.5 2.0 relative luminous intensity(a.u.) ambient temperature ta( o c) 0 10 20 30 40 50 60 70 80 90 o o o o o o o o o o 0 1.0 1.0 0.5 30 o 60 o 90 o 0.5 0 relative intensity(a.u.) radiation angle 450 500 550 600 650 700 0.0 0.2 0.4 0.6 0.8 1.0 relative intensity(a.u.) wavelength(nm) typical electro-optical characteristics curves relative intensity vs. wavelength forward current vs. forward voltage relative intensity vs. ambient temp. relati ve intensity vs. forward current forward current vs. ambient temp. rad iation characteristics
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 6 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen pb el ectrostatic electronagnetic magnetic or radioactive relds anti-static for 750 label packing specification anti-electrostatic bag inner carton label form specification cpn: customer?s production number p/n : production number qty: packing quantity cat: ranks of luminous intensity and forward voltag e hue: rank of dominant wavelength outside carton ref: reference lot no: lot number made in taiwan: production place packing quantity 1. 500 pcs/1 bag, 5 bags/1 inner carton 2. 10 inner cartons/1 outside carton
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 7 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen notes 1. lead forming during lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. lead forming should be done before soldering. avoid stressing the led package during leads formin g. the stress to the base may damage the led?s characteristics or it may break th e leds. cut the led leadframes at room temperature. cutting the leadframes at high temperatures may cause failure of the leds. when mounting the leds onto a pcb, the pcb holes mu st be aligned exactly with the lead position of the led. if the leds are mounted w ith stress at the leads, it causes deterioration of the epoxy resin and this will degr ade the leds. 2. storage the leds should be stored at 30c or less and 70%rh or less after being shipped from everlight and the storage life limits are 3 months. if the leds are stored for 3 months or more, they can be stored for a year in a sealed con tainer with a nitrogen atmosphere and moisture absorbent material. please avoid rapid transitions in ambient temperatu re, especially, in high humidity environments where condensation can occur. 3. soldering careful attention should be paid during soldering. when soldering, leave more then 3mm from solder joint to epoxy bulb, and soldering beyo nd the base of the tie bar is recommended.
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 8 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen prehead laminar wave fluxing recommended soldering conditions: hand soldering dip soldering temp. at tip of iron 300 max. (30w max.) preheat temp. 100 max. (60 sec max.) soldering time 3 sec max. bath temp. & time 260 max ., 5 sec max distance 3mm min.(from solder joint to epoxy bulb) distance 3mm min. (from solder joint to epoxy bulb) recommended soldering profile avoiding applying any stress to the lead frame whil e the leds are at high temperature particularly when soldering. dip and hand soldering should not be done more than one time after soldering the leds, the epoxy bulb should be protected from mechanical shock or vibration until the leds return to room temperature . a rapid-rate process is not recommended for cooling the leds down from the peak temperature. although the recommended soldering conditions are s pecified in the above table, dip or
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 9 of 1 0 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen handsoldering at the lowest possible temperature is desirable for the leds. wave soldering parameter must be set and maintain a ccording to recommended temperature and dwell time in the solder wave. 4. cleaning when necessary, cleaning should occur only with iso propyl alcohol at room temperature for a duration of no more than one minute. dry at r oom temperature before use. do not clean the leds by the ultrasonic. when it is absolutely necessary, the influence of ultrasonic cleaning on the leds depends on facto rs such as ultrasonic power and the assembled condition. ultrasonic cleaning shall be p re-qualified to ensure this will not cause damage to the led 5. heat management heat management of leds must be taken into consider ation during the design stage of led application. the current should be de-rated app ropriately by referring to the de-rating curve found in each product specification . the temperature surrounding the led in the applicat ion should be controlled. please refer to the data sheet de-rating curve. 6. esd (electrostatic discharge) electrostatic discharge (esd) or surge current (eos ) can damage leds. an esd wrist strap, esd shoe strap or antistatic gl oves must be worn whenever handling leds. all devices, equipment and machinery must be proper ly grounded. use ion blower to neutralize the static charge whic h might have built up on surface of the leds plastic lens as a result of friction betwe en leds during storage and handing. 7. other above specification may be changed without notice. everlight will reserve authority on material change for above specificatio n.
technical data sheet 7383/y7c3-aqsb/x/ms everlight electronics co., ltd. http:\\w ww.everlight.com rev 1 page: 10 of 10 device number : dle-0000068 prepared date :10-09-2008 prepared : flourix chen when using this product, please observe the absolut e maximum ratings and the instructions for using outlined in these specificat ion sheets. everlight assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructi ons included in these specification sheets. these specification sheets include materials protec ted under copyright of everlight corporation. please don?t reproduce or cause anyone to reproduce them without everlight?s consent. everlight electronics co., ltd. tel: 886-2-2267-2000, 2267-9936 office: no 25, lane 76, sec 3, chung yang rd, f ax: 886-2267-6244, 2267-6189, 2267-6306 tucheng, taipei 236, taiwan, r.o.c http:\\ www.everlight.com
|
